I’m just really happy about this project today! Since I received my first kit of Amazing Mold Putty®, I’m continually looking for something to make a mold of and asking my husband if he can think of anything to make a mold out of. Well the other day my husband said “ You know how you’re always pulling the wrong chain on the ceiling fan? Wouldn’t it be neat to have a fan pull that looked like a light? Then you wouldn’t have a problem anymore.” I thought that was such a neat idea that the next time I had to run errands I purchased a couple of packages of Christmas lights in two sizes and made a couple of bulbs with chains for the ceiling fans! To start with :
I collected my mold putty, the light bulbs, the chain and the resin.
These two balls are approximately the same size, because you eyeball equal amounts of Part A and Part B of the putty and I roll it into a ball to compare. When you get your two parts rolled up you quickly knead them together. You have a minute here to do that. Once you have the putty kneaded together until it’s all yellow you work rather quickly to get the putty shaped around the object that you are molding. You have around three minutes to do this. Once the putty is around the piece you are molding it will set up rather quickly. When it is completely set up and it is a piece you have put the putty all around, you can cut a split in the side of the mold to pop your piece out that you have been molding:
Easy Peasy!
Once this was complete, I wrapped tape around the mold to hold the split closed so that no resin would leak out and placed it inside a glass. I surrounded the mold with cotton balls to hold it upright without smashing it. I then mixed up some Amazing Casting Resin®:
These two balls are approximately the same size, because you eyeball equal amounts of Part A and Part B of the putty and I roll it into a ball to compare. When you get your two parts rolled up you quickly knead them together. You have a minute here to do that. Once you have the putty kneaded together until it’s all yellow you work rather quickly to get the putty shaped around the object that you are molding. You have around three minutes to do this. Once the putty is around the piece you are molding it will set up rather quickly. When it is completely set up and it is a piece you have put the putty all around, you can cut a split in the side of the mold to pop your piece out that you have been molding:
Easy Peasy!
Once this was complete, I wrapped tape around the mold to hold the split closed so that no resin would leak out and placed it inside a glass. I surrounded the mold with cotton balls to hold it upright without smashing it. I then mixed up some Amazing Casting Resin®:
Same thing here, equal parts of Part A and Part B which you must measure out exactly. (It comes with measuring cups and stirrers. You quickly stir the resin to mix it and pour it into your mold:
At this point you can either insert your chain before it sets up, or drill a small hole in the top after it sets up and glue the chain in. The casting resin sets up very quickly and you can watch the white bloom as it sets up. Once it set, I removed the tape and popped it right out of the mold.
This one looks lit doesn’t it? Anyway now all you might want to do is paint it and seal it and hang it on your ceiling fan. You’ll never have to worry about which chain pull is the light!! I hope this post shows you just how easy it is to make a mold and create something out of that mold.So easy to use and easy to find to purchase. I have personally checked and you can purchase these products at Michaels, Hobby Lobby or online through the Alumilite Corporation. Great stuff!
I wasn’t able to get my light bulbs painted before I had to take my husband to the hospital for back surgery. I thought we would be back home in time to do the painting but there were some complications and at this printing have not made it back home, six days later.
On another note: If you haven’t signed up for the great giveaway that I’m doing, look back a couple of posts and sign up while there’s still time.
I’m so happy to see new followers here on the blog! Maybe you will be the winner of the giveaway!
Barbara
Fabulous idea!!! xoxo
ReplyDeleteSo clever :)
ReplyDeletelove this idea.. as for the fan. I do the same...
ReplyDeleteGreat idea... I always get mixed up which is which to pull... Light or Fan... I always pull the wrong one!
ReplyDeleteGrin....My Idea Light Bulb just went on! Paint the casting with "Glow In The Dark" paint and find it in the Dark....Smile....Hope things are going better....Robert
ReplyDelete